Welcome to the SmallBusiness.com WIKI
The free sourcebook of small business knowledge from SmallBusiness.com
Currently with 29,735 entries and growing.

WIKI Welcome Page
Local | Glossaries | How-to's | Guides | Start-up | Links | Technology | All Hubs
 About · Help Hub · Register to Edit · Editing Help
Twitter: @smallbusiness | Facebook | Pinterest | Google+

SmallBusiness-com-logo.jpeg

In addition to the information found on the SmallBusiness.com/WIKI,
you may find more information and help on a topic
by clicking over to SmallBusiness.com and searching there.


Note | Editorial privileges have been turned off temporarily.
 You can still use the Wiki but cannot edit existing posts or add new posts.
You can e-mail us at [email protected].


Six Sigma

SmallBusiness.com: The free small business resource
Jump to: navigation, search

Template:Distinguish

File:Six sigma-2.svg
The often-used six sigma symbol.

Template:Manufacturing Six Sigma is a business management strategy originally developed by Motorola.[1] Template:As of, it enjoys widespread application in many sectors of industry, although its application is not without controversy.

Six Sigma seeks to improve the quality of process outputs by identifying and removing the causes of defects (errors) and minimizing variability in manufacturing and business processes.[2] It uses a set of quality management methods, including statistical methods, and creates a special infrastructure of people within the organization ("Black Belts","Green Belts", etc.) who are experts in these methods.[2] Each Six Sigma project carried out within an organization follows a defined sequence of steps and has quantified targets. These targets can be financial (cost reduction or profit increase) or whatever is critical to the customer of that process (cycle time, safety, delivery, etc.).[2]

Historical overview

Six Sigma originated as a set of practices designed to improve manufacturing processes and eliminate defects, but its application was subsequently extended to other types of business processes as well.[3] In Six Sigma, a defect is defined as any process output that does not meet customer specifications, or that could lead to creating an output that does not meet customer specifications.[2]

Bill Smith first formulated the particulars of the methodology at Motorola in 1986.[4] Six Sigma was heavily inspired by six preceding decades of quality improvement methodologies such as quality control, TQM, and Zero Defects,[5][6] based on the work of pioneers such as Shewhart, Deming, Juran, Ishikawa, Taguchi and others.

Like its predecessors, Six Sigma doctrine asserts that:

  • Continuous efforts to achieve stable and predictable process results (i.e. reduce process variation) are of vital importance to business success.
  • Manufacturing and business processes have characteristics that can be measured, analyzed, improved and controlled.
  • Achieving sustained quality improvement requires commitment from the entire organization, particularly from top-level management.

Features that set Six Sigma apart from previous quality improvement initiatives include:

  • A clear focus on achieving measurable and quantifiable financial returns from any Six Sigma project.[2]
  • An increased emphasis on strong and passionate management leadership and support.[2]
  • A special infrastructure of "Champions," "Master Black Belts," "Black Belts," etc. to lead and implement the Six Sigma approach.[2]
  • A clear commitment to making decisions on the basis of verifiable data, rather than assumptions and guesswork.[2]

The term "Six Sigma" comes from a field of statistics known as process capability studies. Originally, it referred to the ability of manufacturing processes to produce a very high proportion of output within specification. Processes that operate with "six sigma quality" over the short term are assumed to produce long-term defect levels below 3.4 defects per million opportunities (DPMO).[7][8] Six Sigma's implicit goal is to improve all processes to that level of quality or better.

Six Sigma is a registered service mark and trademark of Motorola Inc.[9] Template:As of Motorola reported over US$17 billion in savings[10] from Six Sigma.

Other early adopters of Six Sigma who achieved well-publicized success include Honeywell (previously known as AlliedSignal) and General Electric, where Jack Welch introduced the method.[11] By the late 1990s, about two-thirds of the Fortune 500 organizations had begun Six Sigma initiatives with the aim of reducing costs and improving quality.[12]

In Template:As of, some practitioners have combined Six Sigma ideas with lean manufacturing to yield a methodology named Lean Six Sigma.

Methods

Six Sigma projects follow two project methodologies inspired by Deming's Plan-Do-Check-Act Cycle. These methodologies, comprising five phases each, bear the acronyms DMAIC and DMADV.[12]

  • DMAIC is used for projects aimed at improving an existing business process.[12]
  • DMADV is used for projects aimed at creating new product or process designs.[12]

DMAIC

The DMAIC project methodology has five phases:

  • Define the problem, the voice of the customer, and the project goals, specifically.
  • Measure key aspects of the current process and collect relevant data.
  • Analyze the data to investigate and verify cause-and-effect relationships. Determine what the relationships are, and attempt to ensure that all factors have been considered. Seek out root cause of the defect under investigation.
  • Improve or optimize the current process based upon data analysis using techniques such as design of experiments, poka yoke or mistake proofing, and standard work to create a new, future state process. Set up pilot runs to establish process capability.
  • Control the future state process to ensure that any deviations from target are corrected before they result in defects. Control systems are implemented such as statistical process control, production boards, and visual workplaces and the process is continuously monitored.

RDMAIC

The RDMAIC project methodology has six phases:

  • Recognize what is most important for your organization, and identify the key initiatives that will have the most impact to your organization.

The rest of the phases are as mentioned in DMAIC

DMADV

The DMADV project methodology, also known as DFSS ("Design For Six Sigma"),[12] features five phases:

  • Define design goals that are consistent with customer demands and the enterprise strategy.
  • Measure and identify CTQs (characteristics that are Critical To Quality), product capabilities, production process capability, and risks.
  • Analyze to develop and design alternatives, create a high-level design and evaluate design capability to select the best design.
  • Design details, optimize the design, and plan for design verification. This phase may require simulations.
  • Verify the design, set up pilot runs, implement the production process and hand it over to the process owners.

Quality management tools and methods used in Six Sigma

Within the individual phases of a DMAIC or DMADV project, Six Sigma utilizes many established quality-management tools that are also used outside of Six Sigma. The following table shows an overview of the main methods used.

Template:Col-2Template:Col-2

Implementation roles

One key innovation of Six Sigma involves the "professionalizing" of quality management functions. Prior to Six Sigma, quality management in practice was largely relegated to the production floor and to statisticians in a separate quality department. Six Sigma borrows martial arts ranking terminology to define a hierarchy (and career path) that cuts across all business functions.

Six Sigma identifies several key roles for its successful implementation.[13]

  • Executive Leadership includes the CEO and other members of top management. They are responsible for setting up a vision for Six Sigma implementation. They also empower the other role holders with the freedom and resources to explore new ideas for Template:Weasel-inlinebreakthrough improvements.
  • Champions take responsibility for Six Sigma implementation across the organization in an integrated manner. The Executive Leadership draws them from upper management. Champions also act as mentors to Black Belts.
  • Master Black Belts, identified by champions, act as in-house coaches on Six Sigma. They devote 100% of their time to Six Sigma. They assist champions and guide Black Belts and Green Belts. Apart from statistical tasks, they spend their time on ensuring consistent application of Six Sigma across various functions and departments.
  • Black Belts operate under Master Black Belts to apply Six Sigma methodology to specific projects. They devote 100% of their time to Six Sigma. They primarily focus on Six Sigma project execution, whereas Champions and Master Black Belts focus on identifying projects/functions for Six Sigma.
  • Green Belts, the employees who take up Six Sigma implementation along with their other job responsibilities, operate under the guidance of Black Belts.
  • Yellow Belts, trained in the basic application of Six Sigma management tools, work with the Black Belt throughout the project stages and are often the closest to the work.

Origin and meaning of the term "six sigma process"

File:6 Sigma Normal distribution.jpg
Graph of the normal distribution, which underlies the statistical assumptions of the Six Sigma model. The Greek letter σ (sigma) marks the distance on the horizontal axis between the mean, µ, and the curve's inflection point. The greater this distance, the greater is the spread of values encountered. For the curve shown above, µ = 0 and σ = 1. The upper and lower specification limits (USL, LSL) are at a distance of 6σ from the mean. Due to the properties of the normal distribution, values lying that far away from the mean are extremely unlikely. Even if the mean were to move right or left by 1.5σ at some point in the future (1.5 sigma shift), there is still a good safety cushion. This is why Six Sigma aims to have processes where the mean is at least 6σ away from the nearest specification limit.

The term "six sigma process" comes from the notion that if one has six standard deviations between the process mean and the nearest specification limit, as shown in the graph, practically no items will fail to meet specifications.[8] This is based on the calculation method employed in process capability studies.

Capability studies measure the number of standard deviations between the process mean and the nearest specification limit in sigma units. As process standard deviation goes up, or the mean of the process moves away from the center of the tolerance, fewer standard deviations will fit between the mean and the nearest specification limit, decreasing the sigma number and increasing the likelihood of items outside specification.[8]

Role of the 1.5 sigma shift

Experience has shown that in the long term, processes usually do not perform as well as they do in the short.[8] As a result, the number of sigmas that will fit between the process mean and the nearest specification limit may well drop over time, compared to an initial short-term study.[8] To account for this real-life increase in process variation over time, an empirically-based 1.5 sigma shift is introduced into the calculation.[8][14] According to this idea, a process that fits six sigmas between the process mean and the nearest specification limit in a short-term study will in the long term only fit 4.5 sigmas – either because the process mean will move over time, or because the long-term standard deviation of the process will be greater than that observed in the short term, or both.[8]

Hence the widely accepted definition of a six sigma process as one that produces 3.4 defective parts per million opportunities (DPMO). This is based on the fact that a process that is normally distributed will have 3.4 parts per million beyond a point that is 4.5 standard deviations above or below the mean (one-sided capability study).[8] So the 3.4 DPMO of a "Six Sigma" process in fact corresponds to 4.5 sigmas, namely 6 sigmas minus the 1.5 sigma shift introduced to account for long-term variation.[8] This is designed to prevent underestimation of the defect levels likely to be encountered in real-life operation.[8]

Sigma levels

See also: Three sigma rule

The table[15][16] below gives long-term DPMO values corresponding to various short-term sigma levels.

Note that these figures assume that the process mean will shift by 1.5 sigma towards the side with the critical specification limit. In other words, they assume that after the initial study determining the short-term sigma level, the long-term Cpk value will turn out to be 0.5 less than the short-term Cpk value. So, for example, the DPMO figure given for 1 sigma assumes that the long-term process mean will be 0.5 sigma beyond the specification limit (Cpk = –0.17), rather than 1 sigma within it, as it was in the short-term study (Cpk = 0.33). Note that the defect percentages only indicate defects exceeding the specification limit that the process mean is nearest to. Defects beyond the far specification limit are not included in the percentages.

Sigma level DPMO Percent defective Percentage yield Short-term Cpk Long-term Cpk
1 691,462 69% 31% 0.33 –0.17
2 308,538 31% 69% 0.67 0.17
3 66,807 6.7% 93.3% 1.00 0.5
4 6,210 0.62% 99.38% 1.33 0.83
5 233 0.023% 99.977% 1.67 1.17
6 3.4 0.00034% 99.99966% 2.00 1.5
7 0.019 0.0000019% 99.9999981% 2.33 1.83

Software used for Six Sigma

Main article: List of Six Sigma software packages

List of Six Sigma companies

Main article: List of Six Sigma companies

Criticism

Lack of originality

Noted quality expert Joseph M. Juran has described Six Sigma as "a basic version of quality improvement", stating that "[t]here is nothing new there. It includes what we used to call facilitators. They've adopted more flamboyant terms, like belts with different colors. I think that concept has merit to set apart, to create specialists who can be very helpful. Again, that's not a new idea. The American Society for Quality long ago established certificates, such as for reliability engineers."[17]

Role of consultants

The use of "Black Belts" as itinerant change agents has (controversially) fostered a cottage industry of training and certification. Critics argue there is overselling of Six Sigma by too great a number of consulting firms, many of which claim expertise in Six Sigma when they only have a rudimentary understanding of the tools and techniques involved.[2]

Some commentators view the expansion of the various "Belts" to include "Green Belts," "Master Black Belts" and "Gold Belts" as a parallel to the various "belt factories" that exist in martial arts.

Potential negative effects

A Fortune article stated that "of 58 large companies that have announced Six Sigma programs, 91 percent have trailed the S&P 500 since". The statement is attributed to "an analysis by Charles Holland of consulting firm Qualpro (which espouses a competing quality-improvement process)."[18] The gist of the article is that Six Sigma is effective at what it is intended to do, but that it is "narrowly designed to fix an existing process" and does not help in "coming up with new products or disruptive technologies." Many of these claims have been argued as being in error or ill-informed.[19][20]

A BusinessWeek article says that James McNerney's introduction of Six Sigma at 3M may have had the effect of stifling creativity. It cites two Wharton School professors who say that Six Sigma leads to incremental innovation at the expense of blue-sky work.[21] This phenomenon is further explored in the book, Going Lean, which provides data to show that Ford's "6 Sigma" program did little to change its fortunes.[22]

Based on arbitrary standards

While 3.4 defects per million opportunities might work well for certain products/processes, it might not operate optimally or cost-effectively for others. A pacemaker process might need higher standards, for example, whereas a direct mail advertising campaign might need lower ones. The basis and justification for choosing 6 (as opposed to 5 or 7, for example) as the number of standard deviations is not clearly explained. In addition, the Six Sigma model assumes that the process data always conform to the normal distribution. The calculation of defect rates for situations where the normal distribution model does not apply is not properly addressed in the current Six Sigma literature.[2]

Criticism of the 1.5 sigma shift

The statistician Donald J. Wheeler has dismissed the 1.5 sigma shift as "goofy" because of its arbitrary nature.[23] Its universal applicability is seen as doubtful.[2]

The 1.5 sigma shift has also become contentious because it results in stated "sigma levels" that reflect short-term rather than long-term performance: a process that has long-term defect levels corresponding to 4.5 sigma performance is, by Six Sigma convention, described as a "6 sigma process."[8][24] The accepted Six Sigma scoring system thus cannot be equated to actual normal distribution probabilities for the stated number of standard deviations, and this has been a key bone of contention about how Six Sigma measures are defined.[24] The fact that it is rarely explained that a "6 sigma" process will have long-term defect rates corresponding to 4.5 sigma performance rather than actual 6 sigma performance has led several commentators to express the opinion that Six Sigma is a confidence trick.[8]

See also

References

  1. ↑ Tennant, Geoff (2001). SIX SIGMA: SPC and TQM in Manufacturing and Services. Gower Publishing, Ltd.. p. 6. Template:Citation/identifier. http://books.google.com/books?id=O6276jidG3IC&printsec=frontcover#PPA6,M1. 
  2. ↑ 2.00 2.01 2.02 2.03 2.04 2.05 2.06 2.07 2.08 2.09 2.10 Antony, Jiju. "Pros and cons of Six Sigma: an academic perspective". http://www.onesixsigma.com/node/7630. Retrieved May 1, 2008. 
  3. ↑ "Motorola University - What is Six Sigma?". http://www.motorola.com/content/0,,3088,00.html. Retrieved 2009-09-14. "[...] Six Sigma started as a defect reduction effort in manufacturing and was then applied to other business processes for the same purpose." 
  4. ↑ "The Inventors of Six Sigma". http://www.motorola.com/content/0,,3079,00.html. Retrieved January 29, 2006. 
  5. ↑ Stamatis, D. H. (2004), Six Sigma Fundamentals: A Complete Guide to the System, Methods, and Tools, New York, New York: Productivity Press, p. 1, Template:Citation/identifier, Template:Citation/identifier, "The practitioner of the six sigma methodology in any organization should expect to see the use of old and established tools and approaches in the pursuit of continual improvement and customer satisfaction. So much so that even TQM (total quality management) is revisited as a foundation of some of the approaches. In fact, one may define six sigma as "TQM on steroids."" 
  6. ↑ Montgomery, Douglas C. (2009), Statistical Quality Control: A Modern Introduction (6 ed.), Hoboken, New Jersey: John Wiley & Sons, p. 23, Template:Citation/identifier, Template:Citation/identifier, "During the 1950s and 1960s programs such as Zero Defects and Value Engineering abounded, but they had little impact on quality and productivity improvement. During the heyday of TQM in the 1980s, another popular program was the Quality Is Free initiative, in which management worked on identifying the cost of quality..." 
  7. ↑ "Motorola University Six Sigma Dictionary". http://www.motorola.com/content/0,,3074-5804,00.html#ss. Retrieved January 29, 2006. 
  8. ↑ 8.00 8.01 8.02 8.03 8.04 8.05 8.06 8.07 8.08 8.09 8.10 8.11 Tennant, Geoff (2001). SIX SIGMA: SPC and TQM in Manufacturing and Services. Gower Publishing, Ltd.. pp. 25. Template:Citation/identifier. http://books.google.com/books?id=O6276jidG3IC&printsec=frontcover#PPA25,M1. 
  9. ↑ "Motorola Inc. - Motorola University". http://www.motorola.com/motorolauniversity. Retrieved January 29, 2006. 
  10. ↑ "About Motorola University". http://www.motorola.com/content/0,,3071-5801,00.html. Retrieved January 29, 2006. 
  11. ↑ "Six Sigma: Where is it now?". http://scm.ncsu.edu/public/facts/facs030624.html. Retrieved May 22, 2008. 
  12. ↑ 12.0 12.1 12.2 12.3 12.4 De Feo, Joseph A.; Barnard, William (2005). JURAN Institute's Six Sigma Breakthrough and Beyond - Quality Performance Breakthrough Methods. Tata McGraw-Hill Publishing Company Limited. Template:Citation/identifier. 
  13. ↑ Harry, Mikel; Schroeder, Richard (2000). Six Sigma. Random House, Inc. Template:Citation/identifier. 
  14. ↑ Harry, Mikel J. (1988). The Nature of six sigma quality. Rolling Meadows, Illinois: Motorola University Press. p. 25. Template:Citation/identifier. 
  15. ↑ Gygi, Craig; DeCarlo, Neil; Williams, Bruce (2005). Six Sigma for Dummies. Hoboken, NJ: Wiley Publishing, Inc.. pp. Front inside cover, 23. Template:Citation/identifier. 
  16. ↑ El-Haik, Basem; Suh, Nam P.. Axiomatic Quality. John Wiley and Sons. p. 10. Template:Citation/identifier. 
  17. ↑ Paton, Scott M. (August 2002). Juran: A Lifetime of Quality. 22. pp. 19-23. http://www.qualitydigest.com/aug02/articles/01_article.shtml. Retrieved 2009-04-01. 
  18. ↑ Morris, Betsy (2006-07-11). "Tearing up the Jack Welch playbook". Fortune. http://money.cnn.com/2006/07/10/magazines/fortune/rule4.fortune/index.htm. Retrieved 2006-11-26. 
  19. ↑ Richardson, Karen (2007-01-07). "The 'Six Sigma' Factor for Home Depot". Wall Street Journal Online. http://online.wsj.com/article/SB116787666577566679.html. Retrieved October 15, 2007. 
  20. ↑ Ficalora, Joe; Costello, Joe. "Wall Street Journal SBTI Rebuttal" (PDF). Sigma Breakthrough Technologies, Inc.. http://www.sbtionline.com/files/Wall_Street_Journal_SBTI_Rebuttal.pdf. Retrieved October 15, 2007. 
  21. ↑ Hindo, Brian (6 June 2007). "At 3M, a struggle between efficiency and creativity". Business Week. http://www.businessweek.com/magazine/content/07_24/b4038406.htm?chan=top+news_top+news+index_best+of+bw. Retrieved June 6, 2007. 
  22. ↑ Ruffa, Stephen A. (2008). Going Lean: How the Best Companies Apply Lean Manufacturing Principles to Shatter Uncertainty, Drive Innovation, and Maximize Profits. AMACOM (a division of American Management Association). Template:Citation/identifier. http://books.google.com/books?id=_Q7OGDd61hkC. 
  23. ↑ Wheeler, Donald J. (2004). The Six Sigma Practitioner's Guide to Data Analysis. SPC Press. p. 307. Template:Citation/identifier. 
  24. ↑ 24.0 24.1 *Pande, Peter S.; Neuman, Robert P.; Cavanagh, Roland R. (2001). The Six Sigma Way: How GE, Motorola, and Other Top Companies are Honing Their Performance. New York: McGraw-Hill Professional. p. 229. Template:Citation/identifier. http://books.google.co.uk/books?id=ybOuvzvcqTAC&pg=PA229&lpg=PA229&dq=%22key+bones+of+contention+amongst+the+statistical+experts+about+how+Six+Sigma+measures+are+defined%22&source=web&ots=jRU19KJVwd&sig=M7jGXg3KoWD7CjUs-ZTNyAjSZls&hl=en&sa=X&oi=book_result&resnum=1&ct=result. 

Further reading


Link to this page: "https://wiki.smallbusiness.com/w/index.php?title=Six_Sigma&oldid=16889"